Paper Cardboard Cake Box Making Machine Diameter 25cm 0.6Mpa Air Pressure

I. Introduction

This machine is suitable for forming cake box bottom base forming such as paper cake tray,circular cake tray,cake tray paper mat,cake paper cardboard tray,paper cake stands,corrugate cake board ,cake drum,paper cake base ,cake cardboard base , paper board mat tray, square paper cake bottom,cake pad,cake paper cardboard pad,paper cake holding tray,paper cake base,paper cardboard cake box bottom forming.

1. Panasonic temperature control module is adopted to control oven.

the temperature can be displayed in degrees, The temperature of baking sheets can be adjusted

up and down .
2. Heat forming machine can memory the parameters , It will start to produce, s long as opening

the number. Thus saving the time of adjusting of the machine and increase the productivity

efficiency.Furnace heated by constant temperature can save energy about 50% than common

ones

3. Feeding part of manual forming machine : automatic air cylinder to press the paper cardboard for forming

4. Take off the product from mold: Can adjust 0~9 times, Heat and glue forming make sure the cake bottom base nice.

II. Features

1. Applied for cake box bottom tray forming, it use Coated paper, gold paper, silver cardboard, white cardboard, greaseproof paper, PE coated paper to form the bottom tray.

2. The bottom tools with heating tube,with top tools pressure to form bottom tray.

3. The machine can be produced from 6 inch to 20 inch round cake box bottom tray or square cake bottom tray

4. Square and round bottom tray with one machine, operation safety, multiple protection

III. Working process

Paper cardboard gluing →Pre heating →Drying →Paper cardboard base forming →Holding →Cutting Edge→Finished product

IV. Main technical parameters

V. Our Service

1. Customer's site installation, training & maintenance available

2. 12-24 hours Online service by Email, Fax, Video Online for basic setup and repairs

3. 12 months warranty for machine, life-long tech. support

4. Recommend equipment of top choice based on your requirements for product;

5. Examining mold drawings on your behalf to confirm optimum structure size meeting high frequency process;

6. Providing assistance in manufacturing and modifying tools;

7. Our engineering instruction will guarantee your productive manufacturing of top-quality products.

. FQA

Questions 01. How Do You Pack the machines ?

RE: Our machines will be packed into wood case, (we will process the wood case and make sure it is exporting standard, and no need fumigation)

Questions 02. Is it difficult to install the machine ?

RE: For standard small machines, the machines will be packed with no take apart, it comes to you to be a complete machine;

you just need to connect power and compressed air to machine, then begin to operate the machine.

For large size machines, we will take the machine apart, on condition that we do our best to keep the machine easy to assembly.

You will get install videos, and install instructions from us.

It will be an ABC thing to install machines at your side.

Questions 03. How Does Customer Use the machines ?

RE: We will provide you operation manual and diagram of machine in English.

For automatic machine and custom machine, we will provide operation videos to you.

Questions 04. Does the machine need compressed air ?

RE: Generally speaking, if your factory with compressed air source, then connect to machine.

If not, please buy a 2Psi -5 Psi air compressor.

If customer request to use Hydraulic pressure, please inform us when put an order.

Questions 05. Does the machine power voltage meet buyers' factory power source?

RE: We can make machine with voltage like:

frequency: 50 - 60HZ Phases: single phase / 3 phases

Voltage: 110V / 220V / 380V/ 415V/ 440V / On request

Please kindly inform us what frequency/phases/voltage you want, when you put order to us.

Questions 06. Could you make die / mould for me, if I buy machine from you?

RE: We design and make moulds up to product sample or drawings, we charge the mould price at facory cost price.

Questions 07. Can I visit you factory to check machines on-site ?

RE: We are manufacturer, and we welcome customers to visit our factory.

We located in Shenzhen, China; you may come to us by following:

a) Via. Hongkong to Shenzhen :

please reach check points between Hongkong and Shenzhen, we will arrange to pick you up from Check-point like Shekou, Lohu

b) Via. Guangzhou to Shezhen;

you may come by train to Shenzhen Luohu Station / Shenzhen North Railway Station.

we will arrange to pick you up from station.

c) Via. Shenzhen Airport :

Please inform us your flight number and contact information before you come, we will meet you at airport.

Questions 08. What Should I bring when I visit your factory?

RE: For special product design and develop, we request you bring a piece of testing material, you can test on our machines on-site.

For common product, it is enough to show us product pictures or drawings.

material together. However, when an HF-welded seam is stressed, the load is absorbed by the material surfaces, which of course means that the HF-welded seam is stronger. Furthermore, the seam created with HF can be welded in a manner that provides a uniform transition without splices between the joined materials. There is no space through which dirt, moisture or bacteria can penetrate and impair the product’s strength and durability.